
11195742-2-A
Required Tools
78
5
2
3
1
6
USA: 1-800-STERLING (1-800-783-7546)
Mexico: 001-877-680-1310
SterlingPlumbing.com
CAUTION: Risk of injury. Do not attempt to cut
tempered glass.
IMPORTANT! Do not remove the protective vinyl
strip from the bottom of the glass panels until
instructed.
Walls must be within 3/8" (10 mm) of plumb.
Cover drain with tape to avoid loss of small parts.
Follow the silicone sealant manufacturer's
instructions for application and curing time.
Installation video available at
SterlingPlumbing.com.
IMPORTANT! The wall jamb must rest flat
against the shower ledge and the wall.
Determine which end of wall jamb will rest on
the shower ledge. Match either the square or
contoured end of the wall jamb to the corner
radius of the shower ledge.
Remove the adhesive backing from both friction
pads. Attach a friction pad to the backside of each
wall jamb approximately 1" (25 mm) above the
shower ledge.
Center the wall jambs on the shower ledge.
Position both wall jambs the same distance from
the front and back edges.
Position the bottom track on the shower ledge.
Place the bottom track between both wall jambs
with the bottom track leg facing the outside of the
shower.
Using the large hex wrench (provided), turn the
expansion mechanism toward the inside of the
shower until the bottom track is secure and the
wall jambs are flush against the shower walls.
Slide both caps toward the center of the top track.
Position the top track to rest on top of the wall
jambs with the rounded face toward the outside of
the shower and the expansion mechanism on the
right.
NOTE: The clamp tabs must press the wall jambs
flush against the wall when the top track is
expanded.
When positioning the top track, insert the clamp
tabs against the wall jambs.
Bypass Bath Doors Bypass Shower Doors
Wall Jamb*
Wall Jamb*
#8-32 x 3/8"
8-32 x 1/4"
Door Panel*
1016784-01**
Top Track
1016784-02**
10082.02
Bracket
(Silver)
(Brass)
1077761-01
1013942
Hex Wrench
(7/64")
(5/64")
1008774
1016784-03**
1016784-04**
1057704-01**
Towel Bar
[18" (457 mm)]
[20" (508 mm)]
[24" (610 mm)]
1057704-02**
1057704-03**
1016785-01**
Bottom Track
(5365EZ-45)
(5375EZ-47)
(5325EZ-57 and 5375EZ-57)
(5305EZ-59 and 5325EZ-59)
1016785-02**
1016785-03**
1016785-04**
1016786-04**
Wall Jamb
(5305EZ)
(5325EZ)
(5375EZ)
(5365EZ)
1016786-03**
1016786-02**
1016786-01**
1044585
Roller
707504
Barrel Nut
1059792
Bushing
1077763-A
Bolt
10195.01
Bumper
1009982
Fastener
1008061**
Guide
1051142-A
Screw
1012706**
Hardware Pack
1008723
Friction Pad
1008723
Friction Pad
(5365EZ-45)
(5375EZ-47)
(5325EZ-57 and 5375EZ-57)
(5305EZ-59 and 5325EZ-59)
10082.05
(Nickel)
Series Number Label
Masking Tape
100% Silicone Sealant
Model Number:______________
*Call Customer Care Center to order replacement parts.
**Finish/color code must be specified when ordering.
Retain this document for future servicing.
Record model number from box for reference.
Installation Guide
5300EZ Series Bypass Shower and Bath Doors
Parts Identification
Top Track
Top Track
Top Track
Cap
1"
(25 mm)
Friction Pad
Same Distance
Top View
Wall Jamb
Leg
Clamp Tab
Expansion Mechanism
Wall Jamb
Outside
of the
Shower
Hex
Wrench
Expansion
Mechanism
Bottom Track
Outside of
the Shower
1093027
Spacer (8 ea.)
Adhesive
Backing
Expansion
Mechanism
x2
Contoured
End
Square
End
Using a level, plumb both wall jambs. Secure with
masking tape.
4
9
Expansion Mechanism
Use the large hex wrench (provided) to turn the
expansion mechanism. Expand the top track until
the top track is secure and the wall jambs are
flush against the shower walls. Tighten one or
two additional turns to secure the top track.
Remove the tape from the wall jambs.
Tape
Comentarios a estos manuales